xref: /dragonfly/sys/bus/u4b/controller/ehcireg.h (revision 56fe6b68029ecfe026662660f3193f380d822be3)
1 /* $FreeBSD$ */
2 /*-
3  * Copyright (c) 2001 The NetBSD Foundation, Inc.
4  * All rights reserved.
5  *
6  * This code is derived from software contributed to The NetBSD Foundation
7  * by Lennart Augustsson (lennart@augustsson.net).
8  *
9  * Redistribution and use in source and binary forms, with or without
10  * modification, are permitted provided that the following conditions
11  * are met:
12  * 1. Redistributions of source code must retain the above copyright
13  *    notice, this list of conditions and the following disclaimer.
14  * 2. Redistributions in binary form must reproduce the above copyright
15  *    notice, this list of conditions and the following disclaimer in the
16  *    documentation and/or other materials provided with the distribution.
17  *
18  * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS
19  * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
20  * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
21  * PURPOSE ARE DISCLAIMED.  IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
22  * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
23  * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
24  * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
25  * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
26  * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
27  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
28  * POSSIBILITY OF SUCH DAMAGE.
29  */
30 
31 #ifndef _EHCIREG_H_
32 #define   _EHCIREG_H_
33 
34 /* PCI config registers  */
35 #define   PCI_CBMEM           0x10      /* configuration base MEM */
36 #define   PCI_INTERFACE_EHCI  0x20
37 #define   PCI_USBREV                    0x60      /* RO USB protocol revision */
38 #define   PCI_USB_REV_MASK    0xff
39 #define   PCI_USB_REV_PRE_1_0 0x00
40 #define   PCI_USB_REV_1_0               0x10
41 #define   PCI_USB_REV_1_1               0x11
42 #define   PCI_USB_REV_2_0               0x20
43 #define   PCI_EHCI_FLADJ                0x61      /* RW Frame len adj, SOF=59488+6*fladj */
44 #define   PCI_EHCI_PORTWAKECAP          0x62      /* RW Port wake caps (opt)  */
45 
46 /* EHCI Extended Capabilities */
47 #define   EHCI_EC_LEGSUP                0x01
48 #define   EHCI_EECP_NEXT(x)   (((x) >> 8) & 0xff)
49 #define   EHCI_EECP_ID(x)               ((x) & 0xff)
50 
51 /* Legacy support extended capability */
52 #define   EHCI_LEGSUP_BIOS_SEM                    0x02
53 #define   EHCI_LEGSUP_OS_SEM            0x03
54 #define   EHCI_LEGSUP_USBLEGCTLSTS      0x04
55 
56 /* EHCI capability registers */
57 #define   EHCI_CAPLEN_HCIVERSION        0x00      /* RO Capability register length
58                                                    * (least-significant byte) and
59                                                    * interface version number (two
60                                                    * most significant)
61                                                    */
62 #define EHCI_CAPLENGTH(x)     ((x) & 0xff)
63 #define EHCI_HCIVERSION(x)    (((x) >> 16) & 0xffff)
64 #define   EHCI_HCSPARAMS                0x04      /* RO Structural parameters */
65 #define   EHCI_HCS_DEBUGPORT(x)         (((x) >> 20) & 0xf)
66 #define   EHCI_HCS_P_INDICATOR(x) ((x) & 0x10000)
67 #define   EHCI_HCS_N_CC(x)    (((x) >> 12) & 0xf) /* # of companion ctlrs */
68 #define   EHCI_HCS_N_PCC(x)   (((x) >> 8) & 0xf)  /* # of ports per comp. */
69 #define   EHCI_HCS_PPC(x)               ((x) & 0x10)        /* port power control */
70 #define   EHCI_HCS_N_PORTS(x) ((x) & 0xf)         /* # of ports */
71 #define   EHCI_HCCPARAMS                0x08      /* RO Capability parameters */
72 #define   EHCI_HCC_EECP(x)    (((x) >> 8) & 0xff) /* extended ports caps */
73 #define   EHCI_HCC_IST(x)               (((x) >> 4) & 0xf)  /* isoc sched threshold */
74 #define   EHCI_HCC_ASPC(x)    ((x) & 0x4)         /* async sched park cap */
75 #define   EHCI_HCC_PFLF(x)    ((x) & 0x2)         /* prog frame list flag */
76 #define   EHCI_HCC_64BIT(x)   ((x) & 0x1)         /* 64 bit address cap */
77 #define   EHCI_HCSP_PORTROUTE 0x0c      /* RO Companion port route description */
78 
79 /* EHCI operational registers.  Offset given by EHCI_CAPLENGTH register */
80 #define   EHCI_USBCMD                   0x00      /* RO, RW, WO Command register */
81 #define   EHCI_CMD_ITC_M                0x00ff0000          /* RW interrupt threshold ctrl */
82 #define   EHCI_CMD_ITC_1                0x00010000
83 #define   EHCI_CMD_ITC_2                0x00020000
84 #define   EHCI_CMD_ITC_4                0x00040000
85 #define   EHCI_CMD_ITC_8                0x00080000
86 #define   EHCI_CMD_ITC_16               0x00100000
87 #define   EHCI_CMD_ITC_32               0x00200000
88 #define   EHCI_CMD_ITC_64               0x00400000
89 #define   EHCI_CMD_ASPME                0x00000800          /* RW/RO async park enable */
90 #define   EHCI_CMD_ASPMC                0x00000300          /* RW/RO async park count */
91 #define   EHCI_CMD_LHCR                 0x00000080          /* RW light host ctrl reset */
92 #define   EHCI_CMD_IAAD                 0x00000040          /* RW intr on async adv door
93                                                              * bell */
94 #define   EHCI_CMD_ASE                  0x00000020          /* RW async sched enable */
95 #define   EHCI_CMD_PSE                  0x00000010          /* RW periodic sched enable */
96 #define   EHCI_CMD_FLS_M                0x0000000c          /* RW/RO frame list size */
97 #define   EHCI_CMD_FLS(x)               (((x) >> 2) & 3)    /* RW/RO frame list size */
98 #define   EHCI_CMD_HCRESET    0x00000002          /* RW reset */
99 #define   EHCI_CMD_RS                   0x00000001          /* RW run/stop */
100 #define   EHCI_USBSTS                   0x04      /* RO, RW, RWC Status register */
101 #define   EHCI_STS_ASS                  0x00008000          /* RO async sched status */
102 #define   EHCI_STS_PSS                  0x00004000          /* RO periodic sched status */
103 #define   EHCI_STS_REC                  0x00002000          /* RO reclamation */
104 #define   EHCI_STS_HCH                  0x00001000          /* RO host controller halted */
105 #define   EHCI_STS_IAA                  0x00000020          /* RWC interrupt on async adv */
106 #define   EHCI_STS_HSE                  0x00000010          /* RWC host system error */
107 #define   EHCI_STS_FLR                  0x00000008          /* RWC frame list rollover */
108 #define   EHCI_STS_PCD                  0x00000004          /* RWC port change detect */
109 #define   EHCI_STS_ERRINT               0x00000002          /* RWC error interrupt */
110 #define   EHCI_STS_INT                  0x00000001          /* RWC interrupt */
111 #define   EHCI_STS_INTRS(x)   ((x) & 0x3f)
112 
113 /*
114  * NOTE: the doorbell interrupt is enabled, but the doorbell is never
115  * used! SiS chipsets require this.
116  */
117 #define   EHCI_NORMAL_INTRS   (EHCI_STS_IAA | EHCI_STS_HSE |          \
118                                         EHCI_STS_PCD | EHCI_STS_ERRINT | EHCI_STS_INT)
119 
120 #define   EHCI_USBINTR                  0x08      /* RW Interrupt register */
121 #define   EHCI_INTR_IAAE                0x00000020          /* interrupt on async advance
122                                                              * ena */
123 #define   EHCI_INTR_HSEE                0x00000010          /* host system error ena */
124 #define   EHCI_INTR_FLRE                0x00000008          /* frame list rollover ena */
125 #define   EHCI_INTR_PCIE                0x00000004          /* port change ena */
126 #define   EHCI_INTR_UEIE                0x00000002          /* USB error intr ena */
127 #define   EHCI_INTR_UIE                 0x00000001          /* USB intr ena */
128 
129 #define   EHCI_FRINDEX                  0x0c      /* RW Frame Index register */
130 
131 #define   EHCI_CTRLDSSEGMENT  0x10      /* RW Control Data Structure Segment */
132 
133 #define   EHCI_PERIODICLISTBASE         0x14      /* RW Periodic List Base */
134 #define   EHCI_ASYNCLISTADDR  0x18      /* RW Async List Base */
135 
136 #define   EHCI_CONFIGFLAG               0x40      /* RW Configure Flag register */
137 #define   EHCI_CONF_CF                  0x00000001          /* RW configure flag */
138 
139 #define   EHCI_PORTSC(n)                (0x40+(4*(n)))      /* RO, RW, RWC Port Status reg */
140 #define   EHCI_PS_WKOC_E                0x00400000          /* RW wake on over current ena */
141 #define   EHCI_PS_WKDSCNNT_E  0x00200000          /* RW wake on disconnect ena */
142 #define   EHCI_PS_WKCNNT_E    0x00100000          /* RW wake on connect ena */
143 #define   EHCI_PS_PTC                   0x000f0000          /* RW port test control */
144 #define   EHCI_PS_PIC                   0x0000c000          /* RW port indicator control */
145 #define   EHCI_PS_PO                    0x00002000          /* RW port owner */
146 #define   EHCI_PS_PP                    0x00001000          /* RW,RO port power */
147 #define   EHCI_PS_LS                    0x00000c00          /* RO line status */
148 #define   EHCI_PS_IS_LOWSPEED(x)        (((x) & EHCI_PS_LS) == 0x00000400)
149 #define   EHCI_PS_PR                    0x00000100          /* RW port reset */
150 #define   EHCI_PS_SUSP                  0x00000080          /* RW suspend */
151 #define   EHCI_PS_FPR                   0x00000040          /* RW force port resume */
152 #define   EHCI_PS_OCC                   0x00000020          /* RWC over current change */
153 #define   EHCI_PS_OCA                   0x00000010          /* RO over current active */
154 #define   EHCI_PS_PEC                   0x00000008          /* RWC port enable change */
155 #define   EHCI_PS_PE                    0x00000004          /* RW port enable */
156 #define   EHCI_PS_CSC                   0x00000002          /* RWC connect status change */
157 #define   EHCI_PS_CS                    0x00000001          /* RO connect status */
158 #define   EHCI_PS_CLEAR                 (EHCI_PS_OCC | EHCI_PS_PEC | EHCI_PS_CSC)
159 
160 #define   EHCI_USBMODE                  0x68      /* RW USB Device mode register */
161 #define   EHCI_UM_CM                    0x00000003          /* R/WO Controller Mode */
162 #define   EHCI_UM_CM_IDLE               0x0       /* Idle */
163 #define   EHCI_UM_CM_HOST               0x3       /* Host Controller */
164 #define   EHCI_UM_ES                    0x00000004          /* R/WO Endian Select */
165 #define   EHCI_UM_ES_LE                 0x0       /* Little-endian byte alignment */
166 #define   EHCI_UM_ES_BE                 0x4       /* Big-endian byte alignment */
167 #define   EHCI_UM_SDIS                  0x00000010          /* R/WO Stream Disable Mode */
168 
169 #define   EHCI_PORT_RESET_COMPLETE      2         /* ms */
170 
171 #endif    /* _EHCIREG_H_ */
172